© Copyright Our Wall
Under the condition of the same paper and ink, due to the problems in the operation process, the finished luster of the album is often different after printing. Without considering the gloss treatment after printing, what are the ways to improve the gloss of custom Spiral YO book printing? Let's take a look!
1, improve the acid wetting fluid
The acidic wetting liquid used in China for decades is mainly chromic acid and phosphoric acid, although diluted, the PH value is still between 3.5 and 5.6. The stronger the acidity is, the greater the resolving power and corrosive power of ink binder and pigment, resulting in rough surface of imprinted film and reduced gloss.
2, reduce ink emulsification
The excessive emulsification of ink in offset printing is mostly caused by large amounts of water and ink in the operation, and the ink layer looks very thick, but the ink molecules have become a state of oil in water, and the luster is very poor after drying, and a series of other failures will occur. Large ink is a very taboo in offset printing, to change this situation, in addition to the quality of operation and technical improvement, it is recommended to use wetting powder, because it has better performance, even if the layout moisture is smaller, it is not easy to dirty. It is easy to operate and makes the finished product shiny.
3, the correct use of dry oil
For advanced bright fast drying ink, under the condition of normal temperature and humidity, it has enough drying capacity. In case of the following situations should be added drying oil: first, in the winter temperature, humidity is low; The second is that the ink should be added in the case of anti-stick agent, removal agent, thin ink oil, etc., should be added to the drying oil. In the process operation, the correct use of dry oil is very beneficial to the formation of gloss in the finished product. This is because the paper takes a certain amount of time to absorb the binder, and in this process, the binder condenses as soon as possible until the conjunctiva is dry, which is the key to the finished product's good luster.
4. Add the diluent
When some ink color is too deep to meet the requirements of spot color printing, it needs to be lightened, which can not only make the ink lighter, but also improve the gloss of the printing product.
5. Add glossy paste
The gloss paste is processed from raw materials with high gloss, which can increase the gloss of the ink, but the amount should not be too large, otherwise it will reduce the drying speed of the ink, and the phenomenon of sticky and dirty and drawing will affect the gloss.
6. Adjust the machine correctly
Whether the thickness of the imprinted ink layer meets the standard also has an impact on the gloss. For example, the pressure regulation is poor, the dot expansion rate is high, the ink layer thickness is not up to standard, and the finished product luster is slightly poor. Therefore, the pressure should be adjusted well, so that the expansion rate of the dot is controlled at about 15%, the ink layer of the printed product is thick, the layer is pulled open, and the luster is also there.
custom Spiral YO book printing https://www.thpkgg.com/Spiral-YO-book.html
Servo Upside down Special Machine is a kind of machine tool that has received wide attention in recent years. It has the characteristics of energy saving and environmental protection, and has been supported by relevant policies. This article will be discussed from two aspects of energy conservation and environmental protection characteristics and policy support.
First, energy-saving and environmental protection features:
1, efficient power system: economic machine tools using advanced electrical drive technology, such as servo motor and inverter, can achieve high precision, low noise and high efficiency of power transmission. Compared to traditional hydraulic or pneumatic systems, electric drives not only respond more quickly, but also effectively reduce energy consumption.
2, save the amount of coolant: in the cutting process, the economic machine tool by optimizing the tool design and cooling system adjustment, reduce the demand for coolant. This not only helps to reduce process costs, but also reduces water consumption.
3, intelligent monitoring and management: economic machine tools are equipped with intelligent monitoring devices, which can real-time monitor equipment operating status, temperature, power and other parameters, and self-diagnosis and adjustment. Optimize workflows, reduce energy consumption and waste generation, and increase equipment utilization with intelligent management systems.
4, green materials and processes: economic machine tools pay attention to the use of green materials and the implementation of environmental protection processes. Recyclable, environmentally friendly materials are preferred, and measures such as reducing waste generation and conserving resources are taken to reduce the impact on the environment.
Servo Upside down Special Machine features
Ii. Related policy support:
1, energy efficiency standards: the state has formulated a series of energy efficiency standards to encourage enterprises to buy and use energy-saving CNC machine tools. At the same time, through the formulation of preferential policies to promote enterprises to upgrade technology and equipment updates.
2. Financial support policies: The government has issued a series of financial support policies to provide financial support for the promotion of Servo Upside down Special Machine. For example, low-interest loans, tax breaks or incentives are provided to encourage enterprises to purchase energy-saving and environmentally friendly equipment.
3. Technical guidance and training: In order to promote the popularization and application of Servo Upside down Special Machine in the market, the government organizes expert teams to conduct technical guidance and training activities. To provide enterprises with industry development trends, advanced technology and management experience, in order to improve the technical level of enterprises and environmental awareness.
4, environmental regulations and standards: the government has strengthened the environmental supervision of CNC machine tool manufacturing enterprises. Enterprises are required to strictly abide by relevant environmental laws and regulations, promote cleaner production processes, and strengthen the management of waste treatment and resource recycling.
In summary, Servo Upside down Special Machine has the characteristics of energy saving and environmental protection, and has been supported by relevant policies. With the continuous improvement of society's requirements for energy conservation, emission reduction and green manufacturing, economic machine tools will be more widely used in the future, and contribute to the transformation and upgrading of China's manufacturing industry.
Servo Upside down Special Machine https://www.zjshuangzheng.com/Servo-Upside-down-Special-Machine-SZ10-151106HV3-14VV.html
mini chainsaws battery operated is mainly used for slicing and crushing of branches, with reliable products, high crushing efficiency and good results. Its power is strong, crushing ability is strong, and it can easily involve and crush branches up to 5cm in diameter. The scope of application is also relatively wide, and then a simple talk about it.
1. Cutting and crushing of branches and leaves in urban greening, fruit farms, forest farms and tea factories
2. Because it is easy to move and does not use electricity, it can also be used for slicing and crushing branches and leaves in parks, colleges, enterprises and institutions, communities and logging areas
3. Crop cutting back to field
4. Use fungus medium wood chips for processing
mini chainsaws battery operated for proper branch handling and improved resource efficiency. The crushed material can be used to cover bare soil, prevent dust and clean the air. Good organic fertilizer, can improve soil and potting soil; Organic fertilizer additive, flower pot soil filler, edible fungi cultivation base material.
mini chainsaws battery operated https://www.keylead.cn/Electrical-Chain-Saw-Supply.html
The machine tool is not suitable for working in a dirty and high temperature and humidity environment, the power supply environment also has higher requirements, the power supply voltage of the machine tool should not be inferior to ±10%, and the corresponding balance and stability. A power grid that is too bad must be equipped with a voltage regulator. In addition to keeping the machine clean and lubricated normally, the following parts must also be carefully maintained:
(1) The guide rail and screw of the machine tool must not be contaminated with dirty water and dirt, once it is contaminated with dirt, it should be wiped with clean cotton yarn and then lightly rubbed with 10# oil of absorbent cotton.
(2) The guide wheel and bearings, for the life of the guide wheel and bearings, should also be too dirty coolant replaced, such as short time do not open the machine tool, no water to let the guide wheel turn for dozens of seconds, so that the guide wheel and the guide wheel between the dirty water thrown out, inject a small amount of oil and then turn for dozens of seconds, so that the oil and dirt in the gap thrown out, and then inject a small amount of oil. So that the guide wheel and bearing are often in a cleaner state.
(3) The coupling and key on the cylinder shaft and the motor, so that the part is always in a tight and secure state of cooperation, once the key is loose and the coupling crashes, the buffer pad and key of the coupling should be replaced immediately. After a long time of commutation with a gap, the keyway on the shaft will be deformed and stretched.
(4) The online cable between the control cabinet and the machine tool, the mop part should have a cover or plastic plate protection, can not be trampled at will, the cable should be in a relaxed free state, can not be pulled by external force, can not force the cable plug, can not frac the cable corrugated sheath.
(5) The console (cabinet) should be handled gently when moving, and the greasy hand should not plug and remove the touch connector or keyboard.
Any part of the bed shall not be knocked or collided, especially because of the over-stroke movement of the wire frame and the bed interference, which will seriously damage the machine parts or accuracy.
(6) Always pay attention to make the conductive block in a good conductive and insulated state between the bed, the workbench pad must be insulated with the bed, the stepper motor drag line should be in a free state, the stepper motor to ensure no dirty water immersion.
steel-inlaid guide rail wire cutting machine https://www.talentcnc.com/Characteristics-of-DK77120-CNC-wire-cutting-machine.html
For printing, most customers do not know how to operate, so many customers will be confused about why there is a color difference in the printing process, why the effect of printing in some positions of the same album is always poor. So what do we need to consider when printing the album? What is the printing process of the album?
dtf adhesive powder factory white hot melt powder Material: Adhesive powder factory is adhesive powder factory white hot melt powder Material: Adhesive powder Factory White hot melt powder Material: Adhesive powder Factory White hot melt powder Material: Adhesive powder factory white hot melt powder Material: Adhesive powder factory white hot melt powder material 105g coated paper, 128g coated paper, 157g coated paper, 200g coated paper, 250g coated paper, 300g coated paper. Most corporate brochures will use 200g as the cover and 157g as the inner page of the paper material for printing, which is easy to print and the price is low. There are also special cover paper, inner coated paper materials, there are also a special paper printed corporate brochures.
Album inside page printing
dtf adhesive powder factory white hot melt powder. Adhesive powder Factory white hot melt powder. Adhesive powder Factory White hot melt powder.
dtf adhesive powder factory white hot melt powder Size: Usually see the size of the album is 16 open, that is, 210×285mm, the reason is that this size saves paper, standard generous paper is 889×1194mm, a generous paper can just print 16 pages, so it is called generous 16 open.
General book size is slightly different, books are printed on standard positive paper, positive size is 787×1092mm, 16 open size is 185×260mm, so most of the fiction and prose books we see in the library are this size.
dtf adhesive powder factory white hot melt powder phase: The process of finishing the film and proofing is calculated per P. Design, film production, proofing, printing, and assembly are generally measured in A4 (210×285㎜). Film is the necessity of the machine, printing proof is the basic basis for the color check of the collar machine.
dtf adhesive powder factory white hot melt powder Middle stage: The key link of printing is printing. The valuation standard is color ream, that is, each color per ream of paper. The printing starts from 5 ream in the open, and the calculation is 5 ream if the value is less than 5 ream. If there is a spot color, such as enterprise special pattern printing spot color (pantone ink) or printing gold, printing silver, etc. Please be sure to indicate, then it will be increased from 4 colors to 5 colors, 6 colors, so that the price is accurate.
dtf adhesive powder factory white hot melt powder Post-production: Usually the processing work after the printing of the printed product. Be sure to indicate: binding (riding nails or glue nails), whether the post-press process has film or UV, die cutting, gold stamping and embossing area should also be written clearly, special materials for printing, packing quantity if there are special requirements. The more specific and accurate the process is, the more accurate the price will be.
Note the following when printing: 1. The distance between the bleeding line and the adhesive powder factory white hot melt powder page and the text must be 3mm from the cutting edge to avoid being cut. 2. Use of color blocks: In color printing, please try to avoid the combination of dark color or full plate color when matching color blocks, otherwise it is easy to produce back printing after printing. Do not cover with white color blocks, so as not to cause trouble when combining. 3. Printing background color: dtf adhesive powder factory white hot melt powder background or background color should not be less than 10% to avoid failure to present the finished product when printing. 4. Wire frame thickness: dtf adhesive powder factory white hot melt powder The wire frame thickness of all input or self-drawn graphics cannot be smaller than 0.1mm. Otherwise, the printed materials may break cables or fail to be presented. In addition, the wire frame can not be set "scale with the image", otherwise the print output will form irregular lines.
dtf adhesive powder factory white hot melt powder Details: During printing design, designers should try their best to use one or two adhesive powder factory white hot melt powder primer colors. Avoid adhesive powder factory adhesive powder factory adhesive powder factory White hot melt powder primer colors. The adhesive powder factory adhesive powder factory adhesive powder factory White hot melt powder primer colors should be adhesive powder factory adhesive powder factory white hot melt powder primer colors. The choice of color should be natural, and there should be harmony when it is excessive and changing, if the difference between the two shades is too large, it will also make people feel uncomfortable and uncomfortable, so the designer must use color cleverly when designing to highlight the focus of the expression of the album, and mobilize the reading interest of consumers through visual effects.
In addition, in the selection of spot color tones, we should follow the unity, in line with the connotation of the album. When printing, it is also necessary to ensure the consistency of the original tone as much as possible. In this way, the artistic effects of dtf adhesive powder factory white hot melt powder can be effectively improved to achieve the purpose of publicity.
dtf adhesive powder factory white hot melt powder https://www.suzhoulongterm.com/dtf-adhesive-powder-factory-white-hot-melt-powder.html
The rail insulators gauge plates manufacturer is an important piece of equipment used in railway maintenance to maintain the collimation and levelness of the track. Its performance and effect can be affected by many factors. This paper will discuss these influencing factors, and classify and elaborate them.
Equipment factors rail insulators gauge plates manufacturer's design and manufacturing quality directly affect its performance and effect. Reasonable structural design and material selection can improve the service life and working stability of the equipment. In addition, the equipment's operating control system, transmission system, hydraulic system, etc., will also have an impact on performance. High-precision sensors and controllers can provide more accurate operating parameters, thereby improving the performance of rail insulators gauge plates manufacturer.
rail factors The collimation and levelness of the rail itself affect the effect of rail insulators gauge plates manufacturer. Deviations and wear during rail installation can cause deformation of the track, which needs to be corrected by using the rail insulators gauge plates manufacturer. The gauge of the rail, the geometry of the rail surface and the straightness of the blank also affect the working effect of the rail insulators gauge plates manufacturer.
The working environment has an important effect on the performance and effect of rail insulators gauge plates manufacturer. Adverse weather conditions (such as high temperature, low temperature, rain and snow, etc.) and climate change will affect the efficiency and accuracy of the equipment. In addition, dust, sand, and water in the workplace can negatively affect the performance of the rail insulators gauge plates manufacturer.
Various factors in the course of operations can also have an impact on the performance and effectiveness of the rail insulators gauge plates manufacturer. For example, the technical level and experience of the operator has a direct impact on the use of the equipment. Reasonable operation methods and skills can improve the working effect of rail insulators gauge plates manufacturer. In addition, the scheduling and intensity of work can also have an impact on the performance of rail insulators gauge plates manufacturer. Overwork and prolonged use can have a negative impact on the performance and life of the equipment.
Maintenance factor rail insulators gauge plates manufacturer Routine maintenance is critical to the performance and effectiveness of the equipment. Regular maintenance and repair can ensure the normal operation of the equipment For example, lubrication and cleaning are routine maintenance work, can avoid damage to the equipment due to friction and pollution. In addition, regular inspection, adjustment and replacement of maintenance parts will also have an important impact on the performance of the equipment.
Working quality factor rail insulators gauge plates manufacturer's working quality is an important index to evaluate its performance and effect. The working quality includes the collimation of the track, the levelness and the maintenance of the gauge. Qualified working quality can ensure the smooth running and safe passage of the train.
Monitoring factors Timely monitoring and feedback is an important means to improve the performance and effect of rail insulators gauge plates manufacturer. High-precision monitoring instruments and meters can monitor the working state of the equipment and the deformation of the track in real time, so as to adjust and correct in time. In addition, the collection and analysis of data is also an important means to optimize performance and results.
rail insulators gauge plates manufacturer https://www.hbrailwayfastening.com/Rail-Insulators-Gauge-Plates.html
1. Heat and oil leakage
As it is a sliding friction drive, more heat will be generated during operation, so that the thermal expansion between the parts and the seal of the Mini planetary geared electric motor is different, thus forming a gap on the mating surface, and the lubricating oil becomes thinner due to the increase in temperature, which is easy to cause leakage. There are four main reasons for this situation. First, the material collocation is unreasonable; Second, the quality of the meshing friction surface is poor; Third, the selection of the amount of lubricating oil added is incorrect; Fourth, the assembly quality and the use of poor environment.
2. Worm gear wear
The worm gear is generally made of tin bronze, and the paired worm material is hardened to HRC4555 with 45 steel, or hardened to HRC5055 with 40Cr and then ground to a roughness Ra0.8μm by the worm grinder. Gear reducers wear slowly during normal operation, and some reducers can be used for more than 10 years. If the wear speed is fast, it is necessary to consider whether the selection is correct, whether the overload operation, and the material, assembly quality or use environment of the worm gear.
3, gear wear
It generally occurs on vertical mounted Mini planetary geared electric motor, mainly related to the amount of lubricating oil added and the type of oil. When installed vertically, it is easy to cause insufficient lubricating oil, when the reducer stops running, the transmission gear oil between the motor and the reducer is lost, and the gear can not get proper lubrication protection. When the reducer is started, the gear is not effectively lubricated, resulting in mechanical wear and even damage.
4, worm bearing damage
In the event of failure, even if the gear reduction secret is well sealed, it is often found that the gear oil in the reducer is emulsified, and the bearing is rusted, corroded, and damaged. This is because after the Mini planetary geared electric motor runs for a period of time, the condensate generated after the gear oil temperature rises and cools is mixed with water. Of course, it is also closely related to bearing quality and assembly process.
Mini planetary geared electric motor https://www.dydzmotor.com/PM-DC-Planetary-Gear-Motor-92JX4500K-80ZY170.html
maintenance for automatic cnc pipe end forming machines technology is widely used in the electric power construction in our country, public and railway construction, boilers, Bridges, ships, furniture, household appliances and decoration industry, its craft is also developing with the progress of modern technology. maintenance for automatic cnc pipe end forming machines must be used in the processing of automobile exhaust pipes. Pipe bending technology is also an indispensable part of automobile muffler processing technology. Here is the daily management of maintenance for automatic cnc pipe end forming machines need to pay attention to what to summarize it.
1. Improve the management organization. maintenance for automatic cnc pipe end forming machines should be set up in the manufacturing department. Responsible for the management and repair of workshop cnc maintenance for automatic cnc pipe end forming machines. Employ some experienced professional technicians and mechanical and electrical engineers with strong professional knowledge, responsibility and some practical work ability, Responsible for the daily management and maintenance of cnc maintenance for automatic cnc pipe end forming machines.
2. Formulate and improve rules and regulations. According to the characteristics of CNC machine tools, gradually develop the corresponding management system, for example, cnc maintenance for automatic cnc pipe end forming machines management system, CNC maintenance for automatic cnc pipe end forming machines Safe operation regulations for machines, operation and use regulations for automatic cnc pipe end forming machines, and maintenance for automatic cnc pipe end forming machines end forming machines technical management methods, cnc maintenance for automatic cnc pipe end forming machines maintenance procedures, so that the management is more standardized and systematic.
3. Establish a sound maintenance for automatic cnc pipe end forming machines file. Establish maintenance for automatic cnc pipe end forming machines Maintenance files and shift records, Record the operation and failure of cnc maintenance for automatic cnc pipe end forming machines in detail. In particular, the maintenance for automatic cnc pipe end forming machines failure time, location, cause, solution and solution process to be recorded and archived in detail, in order to reference in the future operation and maintenance work.
4. Enhanced acceptance. To ensure the quality of the new maintenance for automatic cnc pipe end forming machines, Strengthen maintenance for automatic cnc pipe end forming machines installation, debugging and acceptance work, In particular, the maintenance for automatic cnc pipe end forming machines acceptance of this link, involving the important performance of the machine tool, precision indicators are strictly checked, check the contract, technical agreement, * and domestic standards and acceptance outline of the project. After the debugging of the machine tool, the rs232 interface is used to transmit the data of the machine tool parameters as a backup to prevent the machine tool files (parameters) from being lost.
5. Strengthen the construction of maintenance team. cnc maintenance for automatic cnc pipe end forming machines Set machine, electricity, liquid (gas), light in one of the high-tech products, high technical content, operation and maintenance difficulty. Therefore, it is necessary to establish a high-quality maintenance team to meet the needs of maintenance for automatic cnc pipe end forming machines. maintenance for automatic cnc pipe end forming machines is carried out in various ways, such as installation and debugging and internal learning classes The operation, maintenance, programming and management of forming machines shall be trained for automatic cnc pipe end forming machines.
maintenance for automatic cnc pipe end forming machines https://www.john-sheng.com/CNC-Tube-End-forming
Select the appropriate mounting method depending on the space used and the mounting position (front and rear mounting, quick locking of screws, clings, rivets or din 41612 type e connectors manufacturer itself, etc.). Select the appropriate mounting method depending on the space used and the mounting position (front and rear mounting, quick locking of screws, clings, rivets or din 41612 type e connectors manufacturer itself, etc.). General signal transmission has no special requirements for the impedance of the din 41612 type e connectors manufacturer.
din 41612 type e connectors manufacturer plug-ins are widely used electronic components in modern manufacturing and are particularly important for improving manufacturing processes. In everyone's production activities, it goes without saying that the din 41612 type e connectors manufacturer is for electronic devices. An electronic product without a din 41612 type e connectors manufacturer is useless. Although they are the main body, and the din 41612 type e connectors manufacturer is only an attachment, their necessity is the same, especially when it comes to enabling the transmission of information in mechanical devices.
So how do you choose to apply din 41612 type e connectors manufacturer?
1. Structural size: The size of the din 41612 type e connectors manufacturer is very important. The connections in the product have certain space limitations, especially the din 41612 type e connectors manufacturer on the single board, and cannot be interfered with other components. Select the appropriate mounting method according to the space used and the mounting position (front and rear mounting, quick locking of screws, clings, rivets or din 41612 type e connectors manufacturer itself, etc.). And shape (straight, curved, T-type, round, square).
2. Matching resistance: Some signals require impedance, especially RF signals, which require more stringent matching resistance. When the impedance is not matched, it will cause signal reflection, which will affect the signal transmission. General signal transmission has no special requirements for the impedance of the din 41612 type e connectors manufacturer.
3. Shielding: With the development of communication products, electromagnetic compatibility has received more and more attention. When selecting the din 41612 type e connectors manufacturer, there needs to be a metal housing, and the cables need to have a shielding layer to connect to the metal housing of the din 41612 type e connectors manufacturer, To achieve the effect of shielding. The cable shield can also be wrapped in copper.
4. Anti-insertion: Anti-insertion has two aspects: On the one hand, the din 41612 type e connectors manufacturer itself is rotated 180 degrees, and the din 41612 type e connectors manufacturer is connected incorrectly, resulting in an incorrect signal connection. At this time, take care to select the din 41612 type e connectors manufacturer to avoid incorrect insertion as much as possible, or make the installation unique by adjusting the relative position of the din 41612 type e connectors manufacturer; On the other hand, in order to reduce the type of material, several signals use the same din 41612 type e connectors manufacturer, and then there may be A plug B situation. It should be noted that if this situation will lead to serious consequences (not A simple alarm, but devastating), then A and B must choose different types of sockets.
5. Reliability of din 41612 type e connectors manufacturer :din 41612 type e connectors manufacturer is used to connect signals, so the connection part should be reliable (such as surface contact is better than point contact, Pinhole than plate spring, etc.).
6. Use environment: When din 41612 type e connectors manufacturer is used in outdoor, indoor, high temperature, high humidity, salt spray, mildew, cold and other environments, there are special requirements for din 41612 type e connectors manufacturer.
7. Practicality: In the process of selecting din 41612 type e connectors manufacturer, try to select common parts, especially between the same product series. The selection of din 41612 type e connectors manufacturer is very practical and can reduce the variety of materials, increase the quantity, reduce costs and reduce supply risks.
din 41612 type e connectors manufacturer https://www.kujunconnector.com/TYPE-E-Connectors
The use of GPS locators is more and more widespread, especially the driver friends must be no stranger, and many friends want to know whether GPS locators can operate normally in harsh environments. In general, when the temperature is too high or too low, normal electronic products will affect the normal operation of the equipment. Let's take a look at how gps hidden tracker works in special environments.
Just like in the winter, some electronic devices will not be able to charge the situation, so the outdoor operation also needs to receive satellite signals GPS locator will be affected by environmental factors. The acceptable scale of the locator in the low temperature environment is -20-70 degrees, and many people may think that this is not important, and there will not be such a high temperature at room temperature. In fact, this temperature scale only means that the GPS locator can maintain its operation, but it does not necessarily reach the optimal operating state. In the northern winter, minus 20 degrees is also common, not to mention the temperature can be even lower in some harsh environments. In the summer, it is not possible to ensure that the vehicle is parked in a cool parking lot every time, as long as it is outdoors, the car is a closed space, and the temperature inside the car is higher than that outside the car, not to mention the car directly exposed to the sun. A stable ambient temperature of 15-35 degrees is the best condition for the GPS locator to continue working.
If the above two climate conditions are present, and the locator is still located outside the car, such as the bumper in the trunk of the car, the vehicle directly exposed to the environment will be more constrained. If the operating temperature of the GPS locator exceeds the acceptable scale, it will automatically shut down and stop the operation to maintain the components of the device, and will not automatically damage the device. People often ask if exposure locators will explode? In fact, the explosion of the GPS locator is mostly caused by the line problem, and the incorrect connection of the line leads to the change and conflict of various parts of the device. If your GPS locator is installed correctly, this is rarely the case. The same is true for low-temperature environments.
The normal operation of gps hidden tracker in harsh environment also depends on the specific situation. In harsh weather conditions, the normal operation of GPS locator will be affected, not only the ambient temperature, but also the signal reception of GPS locator in thunderstorm weather. If the climate is too bad, it is recommended that we still reduce the go out, of course, we usually have to pay attention to the GPS locator settling environment and wiring methods.
gps hidden tracker https://www.eelinktracker.com/Magnetic-GPS-Tracker/